Reloading bench that fits in a box? The Classic Lee Loader kit in the red container stands in for the green equipment – and it’s a whole lot more portable.
Among a recent treasure trove of used reloading gear presented by a friend, I discovered an old but familiar item, a Lee Precision Classic Lee Loader. These small kits have been sold for more than 60 years. Simple, affordable, and portable, they can restore a supply of fired brass cases to fully functional cartridges pretty much anywhere, from a tailgate to a remote cabin. My reloading career began with a Lee kit years ago in a less exotic location – my bedroom, at the ripe old age of fourteen.
And, instead of metallic cartridges, I was reloading shotgun shells. The reloading bench was the top of my dresser, and the entire press was stored in a drawer. The process was a lot more labor-intensive than my current progressive-press loading system, but the final product – a 2 12 Gauge target load – was every bit as good if not better.
If you’re just getting started with reloading I’d also suggest following this link to read more on the subject.
Sadly, the shotgun version is no longer cataloged. However, Lee still lists their kits for a number of rifle and handgun calibers. The price, at under $50, is right.
Shop for your caliber Classic Lee Loader at Optics Planet. Complete Classic Lee reloading kit. From here it’s just a matter of suitable components, starting with a supply of good clean cartridge cases.
Table of Contents Classic Lee Loader Test-RunComponentsCase ResizingThe Lee Loader Reloading ProcessWe Have A Cartridge!Test FireUseful ExtrasCase PreparationPowder ChargeOther Good InvestmentsLast Thoughts Classic Lee Loader Test-Run
Since the gifted .30/06 Classic Lee was in pristine condition, I decided to give it a try. I had a good collection of components, but one possible stumbling block was powder suitable for the kits scoop measure. Ingredients for the .30/06 recipe. No guessing here! Reloading is safe with common sense. Go rogue and bad things will happen. Components
Of the many powders with different burn-rates and densities, only some will be safe for a given caliber and its projectiles. Beyond that, specified charges must be used to maintain safe pressure-parameters. My longstanding 06 hunting load, fueled by IMR 4350, is charged by weight (in grains) from a carefully adjusted powder measure. But the kit uses a fixed-volume powder scoop.
Lee provides a chart that shows suitable powders for popular bullet weights, but IMR 4350 wasnt listed. Luckily, of the three propellants shown for 150-grain bullets, my on-hand cannister of IMR 4064 did appear. From there I was in business through a stash of CCI 200 Large Rifle Primers, Hornady 150-grain Interlock Spire-points and a collection of cartridge cases.
The starting point was a batch of clean cases with identical headstamps. A box of once fired 06 brass had that covered but posed a concern, having been fired in several rifles. The Lee kit includes clear and easy to follow directions, starting with a diagram of the steps. Not mentioned there (but covered later on) is the essential resizing process. Case Resizing Generic cartridge nomenclature and reloading steps, minus the resizing process. Using Lee’s system, bottle-necked cartridge brass is neck-sized only. The available straight-walled handgun choices are full-length resized, which can require extra elbow grease.
If you have a supply of clean Boxer-primed (standard U.S.) cases, fired in your gun, the Lee resizing die should work fine. Brass is a perfect material for a metallic cartridge because of its elasticity. The same pressure that expels the bullet will expand the case to seal it against the chambers walls. As the bullet exits and pressure subsides, the brass case will contract for easy extraction from that particular chamber.
However, because of tolerances, it could be too large to fit others. For this reason, most of us squeeze our fired cases back to factory specs via full-length resizing dies and high-leverage presses. The process requires lubricant and considerable force a challenge for a simple hand tool. Resizing only the forward section (bullet-gripping neck) requires a lot less the reason why Lee kits are designed to neck-size bottle-necked cartridges.
Case lube wasnt mentioned in the directions but, playing it safe, I did apply a swipe of Imperial Sizing Die Wax to the first 06 case. Resizing was much easier than expected so I skipped it for the rest. Imperial Redding Sizing Die Wax 2 Ounce Tin Md: 07600 Non-liquid sizing die lube packaged in 2oz. containerThe original – a favorite among reloaders $14.95 Buy on Amazon The Lee Loader Reloading Process
I planned on photographing each of the seven steps but, as it turned out, Lee already had the process covered via clear photos. Contents of the Classic Lee kit for reference, below.
Step 1: Knock out the old primers.
Step 2: Drive the case into the tool flush with the end.
Step 3: Insert a primer into the locating ring
Step 4: Use the decapping chamber and tap the rod to free the case.
Step 5: Add your powder.
Step 6: Insert the bullet through the top.
Step 7: Insert the bullet sealer and tap into place. Next up, the seven-step process. Note the Dos and Don’ts – sound advice! Step #1: Deprimed case after removal from the decapping chamber. Carbon deposits should be removed from the pocket before a new primer is seated. Step #3: Resized case, ready for priming. A CCI 200 Large Rifle Primer has been carefully positioned in the Lee priming chamber. Step #5: Ready for charging, using the scoop. The funnel isn’t essential, but it does help prevent spillage of expensive powder. FYI, there are 7000 grains in a pound. That’s 150 shots, using 46.5-grain scoops of IMR 4064 (about 25 cents apiece from this cannister).
Step #5 Note: Before charging the first primed case, I filled the kits 3.4 cc dipper with a leveled charge of IMR 4064. My powder scale indicated a weight of 46.5 grains – more than the 45.6 grs. listed for the dipper, but still below the data shown in my Hornady manual. Several more practice scoops produced similar weights, plus or minus a few tenths of a grain – deemed close enough. Step #7: Bullet seating. Depth (and cartridge overall cartridge) can be regulated adjusting the height of the upper stop collar. Once COL is established, the knurled locknut can be cinched against the collar.
Step # 7 Note: Prior to seating the first bullet, I unscrewed the dies locknut and backed out the stop collar. Then, through trial and error (using vernier calipers), I gradually increased the seating depth to coincide with my existing handload. The nut was locked when cartridge overall length was 3.230, identical to the C.O.L. shown in my now-dated Hornady Handbook (third Edition). We Have A Cartridge!
The first .30/06 Lee handload looked every bit as good as my press-produced cartridges. It also chambered without difficulty in a Remington Model 700 (carefully loaded on my outdoor range). Same for the next two, at which point I halted production to set up a shooting test. First three handloaded rounds, ready to go. All chambered without difficulties in this Remington Model 700 .30/06. Test Fire
Figuring the Lee handload would shoot close to my established hunting load, I placed a target at 100 yards, set up the chronograph, and fired one shot off sandbag rest. It hit almost dead-center and extracted without issues. As expected though, velocity was only 2559 fps (15 feet off the muzzle), a tad faster than Lees 2532 fps claim, probably due to my slightly heavier charge and/or the M-700s 24 barrel.
Things were lookig promising but the next two shots clocked 2469 and 2415 fps – one heck of a velocity spread! The 144-fps extreme no doubt explained a vertically strung 2 group – not the norm for this rifle.
The problem coming to mind was my dipper technique, called good after just a few practice dips. To find out, I compared a few more dipper charges to the scale. Results were inconsistent so I used the dipper and scale to assemble three more cartridges with weighed 46.5-grain charges.
Big improvement; 2478, 2478, and 2481 fps (an extreme spread of only 9 fps)! The second series coincided with the two slower shots from the first, to form a 5-shot a 1 group not stellar, but still useful. Velocity was only around 100 fps faster than a .30/30, however the load is subject to improvement through more throttle (see below). .30/06 Lee Loader experiment, showing two 3-shot, 100-yard groups. The first (circled in red) using scooped charges corresponded with a high 144 fps velocity spread. The second group, fired with weighed charges, cut the spread to a respectable 9 fps. With the exception of the highest shot, both groups measured around 1 3/4″ – not spectacular but still useful.
Assuming a Lee kit is used with consistent brass and powder charges, theres really no reason why it shouldnt produce accurate cartridges. Actually, many picky handloaders neck-size to achieve precise chamber alignment, which often translates to tighter groups. Useful Extras
Bottle-necked cartridge cases tend to stretch lengthwise during multiple firing cycles and, although less of an issue with neck-sized brass, maximum case length should never be exceeded! The neck needs some clearance to release the bullet. If pinched against the chamber, dangerous pressures could develop. Case Preparation
Before attempting to reload the above Remington .30/06 cases, I measured their lengths with a dial caliper. Having only been fired once, they hovered around 2.488, safely below 2.494 max. If not, their necks wouldve required a trim and, among the various devices sold for this purpose, the simplest is Lees caliber-specific case-pilot & cutter system.
Case trimmer, Gauge/Holder: Includes a caliber-specific shell holder and pilot to regulate length.
Case trimmer, Cutter & Lock Stud: Includes a universal mount for the necessary shell holder, and universal case cutting tool. Sale Lee Precision Cutter and Lock Stud Made in USAWorks on all brass less than .475 base diameter $9.45 Buy on Amazon
Case Chamfer Tool: Chamfers and deburrs the outside and inside of case necks (to ease bullet seating). Can also be used to deburr the crimped primer pockets common to military brass. Lee Precision Chamfer Tool Package length: 12.192 cmPackage width: 5.842 cm $10.36 Buy on Amazon
Primer Pocket Cleaner: Removes fouling from both small and large primer pockets for consistent seating of new primers. Sale Lee Precision Primer Pocket Cleaner Double ended design cleans both large and small primer pocketsInsures that primers can be fully seated for better accuracy and safety $1.49 Buy on Amazon Case prep tools: (L) Lee .30/06 Pilot screwed into a Universal Cutter, (C) Lee .30/06 Shell Holder screwed on to a Universal Mount, (R) Lee’s Primer Pocket Cleaner. The case chamfering tool isn’t from Lee, but it works the same way. Powder Charge
The obvious downside to the above handload was its low velocity – expected since its 46.5-grain charge of IMR 4064 was a full grain under Hornadys starting load. Hornadys data spanned 47.5/2700 fps to 52.6/3000 fps from a 22 barrel.
My pet IMR 4350 hunting load does 2850 fps. Lees chart shows a max of 288 fps, using 52 grains of IMR 4064. And, to reach that level, two simple speed-boost solutions are available. Lee’s .30/06 load data, based on the kit’s 3.4cc dipper. Note the “NEVER EXCEED” and Min OAL figures. Overall length affects velocity so those shown here are “calculated” examples.
Powder Measuring Kit: Invest in a full set of dippers (15 in all from .3.0 4.3 CCs) with comprehensive data. Lee Precision Powder Measure Kit Made in USA15 graduated powder dippers from .3cc to 4.3cc $18.49 Buy on Amazon
Lee Safety Powder Scale: Highly worthwhile! Provides greater load flexibility (see below). Also, the best way to confirm safe and accurate powder charges. Sale Lee Precision Safety Scale Red Simple to useHigh Quality Construction $33.99 Buy on Amazon Consistent dipper charges require practice. This one weighed 46.1 grains; four-tenths shy of the 46.5-grain average. Also, a finer-grained propellant (like H-414) would be easier to measure with the scoop. Or skip the dipper, buy a reloading manual, and take advantage of other propellant and bullet choices through weighed charges. Other Good Investments
Word-of-mouth load recipes are risky and Internet sources are often no better. Lees chart is the much safer starting point, but a currently dated reloading manual is still worth every cent. One example of several: The Hornady Handbook (now in its 11th edition), is available as printed and electronic versions. Hornady 11th Edition Handbook of Cartridge Reloading Over 1,000 pages of data for over 200 different calibersMultiple new cartridges including 6mm ARC, 6.5 and 300 PRC, 350 Legend, 224 Valkyrie, and 28 Nosler $65.61 Buy on Amazon
Like others, it contains useful reloading information and covers a wide range of loads with further value for cross reference purposes.
A caliper (dial or digital) will provide the measurements needed to control crucial cartridge dimensions. A useful last step: Label each box of handloads with all of the pertinent data to include the components, overall length, and the assembly date. Last Thoughts
Given these uncertain times, ongoing scarcity of ammunition and its escalating cost, a stash of brass and an inexpensive reloading system could make sense. The Classic Lee Loader is presently available in fifteen calibers, including six popular handgun picks.
For projects like a 500-round batch of .223s, Ill stick with the press-equipped reloading bench, thanks. But the equipment and components constitute a large pile of stuff, not very conducie to mobility. For lower volume production typical of cartridges like the 06 (and many others), a Classic Lee Loader could well be the perfect on-the-move alternative.
Granted, components arent cheap, but they can be procured piecemeal through local or shipped sources. These items, and the equipment, also appear at gun shows and even garage sales, for substantial savings. The most expensive component is typically the cartridge case. But, thanks to Lees more gentle sizing process, they should be good for at least several firings – if not a heck of a lot more!